Removing a battery can be scary. Many people fear damage and data loss. But a clear set of steps removes doubt.
This guide shows how to remove the battery from an iPhone 6S Plus safely. You will learn all steps, risks, and tools needed to do it right.
You should keep reading. The process is detailed. You will see why each step matters. You will have confidence to attempt removal or know what to tell a technician.
What tools are required for removal?
Removing the battery from an iPhone 6S Plus needs special tools. If you try without proper tools, you can break parts. You need tools that fit tiny screws and sensitive parts. The right tools reduce risks. Picking cheap or wrong tools makes the job harder.
Here are the common tools you will need to open and remove the battery from an iPhone 6S Plus.
When you start, you will see that an iPhone is not like a regular phone. The parts inside are packed tight. Without correct tools, you might damage the screen or internal parts. You need tools that let you work gently and precisely. Most people buy a repair kit made for iPhone repairs. These kits include small tools you cannot find in your home tool box. Below is a list of tools you must have:
Basic tool list
- Pentalobe screwdriver (for outside screws)
- Phillips screwdriver (for internal screws)
- Plastic opening picks
- Suction cup
- Spudger
- Tweezers
- iOpener or heat source (optional but helpful)
| Tool | Purpose |
|---|---|
| Pentalobe screwdriver | Remove bottom screws near charging port |
| Phillips screwdriver | Remove screws holding components inside |
| Suction cup | Lift screen gently |
| Spudger | Disconnect battery connector |
| Opening picks | Separate adhesive |
You will also want a clean work surface. Lay down a soft cloth or mat. This keeps screws from rolling away. Keep small containers to hold screws once you remove them. If screws mix up, you might put the wrong screw in the wrong place. This can damage the phone.
After you prepare tools, you will find the process easier. It helps to follow steps slowly. Rushing will increase risk of error. With the right tools and care, you can finish this task without damage. Having the right tools is the first step to success. It gives you control and confidence.
Why follow Apple-specific steps?
Apple is known for tight and compact design. Every part inside an iPhone has a specific place. The battery in an iPhone 6S Plus is glued into the case. It is not like older phones where you could just pop the battery out. You have to follow the correct Apple-specific steps so you do not break other parts.
Following Apple-specific steps means you respect how Apple builds the phone. This makes it possible to remove the battery safely and avoid damage.
If you do not follow the correct steps, you may tear cables or break connectors. Apple phones use very thin cables that can break easily. One wrong move can make the phone stop working. This is why a step-by-step Apple-based method matters.
Inside an iPhone 6S Plus, the battery sits under many parts. The screen, home button cable, and battery connector are all connected to the logic board. Apple designed the battery to be replaceable, but only with proper care. The steps also protect the battery from puncture. A punctured lithium battery can catch fire or swell. You want to avoid that at all costs.
There are many guides online, but not all follow Apple-specific logic. Some guides skip steps or give shortcuts. These shortcuts may save time but increase the chance of damage. You should follow steps that respect Apple’s design and order of operations.
Let’s break down why each step matters:
Step order matters
- Turn off the phone first. This prevents short circuits.
- Remove bottom screws. This lets you open the display slowly.
- Lift display carefully. The display is attached with thin cables.
- Disconnect battery before other parts. This reduces power risk.
Each of these steps protects a part of the phone. If you skip disconnecting the battery first, a screwdriver slip can short the logic board. The logic board is the brain of the phone. Damage there can be expensive to fix.
Following Apple-specific steps also protects your data. If the phone powers on during the process, you can lose information or corrupt files. So the order and care in steps keep the phone safe electronically and physically.
In short, Apple-specific steps are not suggestions. They are a roadmap that keeps the device intact and working.
Which risks occur during disassembly?
When you open an iPhone 6S Plus, you enter a world of tiny parts. Many risks can happen in this process. You must understand these risks before you start. This helps you plan and avoid common mistakes.
Disassembly has risks like damaging cables, puncturing the battery, or losing screws. Knowing these helps you prepare and reduce chances of error.
The iPhone 6S Plus battery is a lithium polymer type. It can be dangerous if punctured or bent. If you apply too much pressure or use metal tools in the wrong place, the battery can swell or leak. This can cause fire or smoke. You do not want that.
Inside the phone, many parts are connected by thin ribbon cables. These cables look strong but are fragile. They can tear easily. Once torn, they cannot be repaired except by soldering. Soldering inside this phone is very hard and risky. So you want to prevent tearing them.
Another risk is the adhesive under the battery. It holds the battery tightly in place. Pulling too hard without heating or loosening the adhesive can stretch or snap something. This can bend the battery or break the battery strips. Once the battery is bent, it may swell or stop working properly.
There is also a risk of mixing up screws. The screws inside an iPhone are not all the same size. If you put a longer screw where a short one should go, it can pierce the logic board or other parts. This may destroy the board. To avoid this, use containers and mark where each screw came from.
Finally, static electricity can damage the phone’s logic board. A static discharge from your body can fry circuits. To reduce this risk, work on a grounded mat or touch a metal object before handling parts. This drains static from your body.
Here is a list of common risks and how to reduce them:
Risks and prevention
| Risk | Prevention |
|---|---|
| Battery puncture | Use plastic tools and gentle force |
| Ribbon cable tear | Lift parts slowly, do not force |
| Screw mix-up | Use labeled containers |
| Static damage | Ground yourself before work |
| Adhesive stretch | Heat gently to soften adhesive |
When you understand these risks, you can avoid them. You will move slowly and think before you act. This keeps both you and the phone safe.
How to identify correct replacement battery?
After you remove the old battery, you will need a replacement. But not all batteries are the same. Apple uses batteries with specific size, voltage, and connector type for the iPhone 6S Plus. If you pick the wrong battery, it may not fit or charge properly.
You need to identify the correct replacement battery by matching it with Apple’s specifications and quality standards. This ensures it works well and lasts long.
The first thing to check is the model number. Apple batteries for the iPhone 6S Plus are labeled with a specific model code. This code matches Apple’s design. If the code does not match, the battery may not fit or perform well.
Next, check the capacity. The correct battery capacity gives you the battery life Apple intended. A lower capacity battery will drain fast and give poor performance. Look for batteries that match or exceed the original capacity. Do not choose batteries with much higher capacity if they are not certified. Some fake batteries claim high numbers but are unsafe.
Connector type is important too. The battery connector must be the same shape and size as the original. If the connector is wrong, it won’t attach to the logic board. Apple batteries have a flat connector with a metal cover. Make sure the replacement has the same type.
You should also check for quality certifications. Batteries with CE, RoHS, or similar badges show some testing and safety standards. This matters for safety. A bad battery can overheat or swell. Always avoid cheap unbranded batteries with no certification.
Here is a table to help you compare batteries:
Replacement battery comparison
| Feature | Correct Apple 6S Plus Battery | Incorrect Battery |
|---|---|---|
| Model number | Matches Apple spec | Does not match |
| Capacity | Same or very close | Much lower or fake values |
| Connector type | Exact match | Different or forced fit |
| Certification | Yes | No |
To identify the correct battery, inspect the label and specs closely. You can ask the seller for a datasheet. If you are not sure, compare pictures online. Many guides show what a real battery looks like. Use those as reference.
When you have the correct replacement battery, install it gently. Avoid touching metal contacts with bare hands. Oils from your fingers can cause poor connection or corrosion over time.
Replacing the battery is not just about size. It is about quality and safety. Take your time to choose a good battery. This ensures the phone works well and stays safe.
Conclusion
Removing and replacing a battery in an iPhone 6S Plus is not simple, but with the right tools, steps, and care, it can be done safely and correctly. Understanding risks and selecting the right battery makes a big difference.
